How to install Photo etching on metal correctly? Using a water purifier properly will achieve maximum filtration capacity, save water, and ensure the life of the machine and filter core. Moreover, refer to the content below to know how to use the Aqua water purifier.
To use the stainless-steel filter mesh effectively. First, it is necessary to know certain precautions during installation and during and after using the machine.
Choosing the location of Photo etching on metal is extremely important as one of the basic factors to help the water purifier avoid external influences that affect its lifespan and filterability. The most suitable water purifier installation location should meet five factors.
It is recommended to use a cabinet-type water 5-micron stainless steel filter mesh. Moreover, the reasonable position to be advised today is to place the sound under the kitchen cabinet or under the sink, very neat and aesthetic. In addition if the space under the kitchen cabinets is not enough.
Install the machine in an empty space near the corner of the wall, near the kitchen, or near the water source for convenient use, about the size of a small refrigerator. Furthermore, it also doesn't take up too much space in your home. Inlet water pressure must be ensured.
In the first use, it is recommended to use 5-micron stainless steel filter mesh. Moreover, let the water drain for 20-30 minutes when the water is completely clear before using.
And, open the water valve for 5 minutes so that the water begins to flow more stably.
Never insert the faucet end of the machine into the hot water source to avoid damage to the water supply cord. Moreover, do not freeze the water filtration system. Finally, do not close the drain hole. Because of that, it will be very easy to damage the water filter elements.
During the operation of the cleaner, careful observation is recommended. The purpose is to check the Photo etching on metal speed, filter core, filter water quality. This helps to detect whether the water purifier has any problems. Make the machine operate stably over time.
In case of problems, you should turn off the power, remove the waterline, and repair it yourself. Then, it is necessary to contact the warranty technician. Also, when away from home, unplug the power and lock the water filter system to ensure safety and long life for the machine.
The core should be replaced as recommended. If using expired water filters, the water after being treated through the water purifier is more dangerous than untreated water. Output water will not be clean. Drinking is not good for health, easy to cause disease.
After replacing the Photo etching on metal, a water change should be carried out to ensure that the operation is free from residual contamination. As well as avoiding the situation of causing water blockage when using.
To learn the diagram of Aqua water purifier. The first part of the machine can be seen as the inlet valve. Install an additional lock to adjust the amount of water and shut it off when necessary.
Next are three raw water 5-micron stainless steel filter cores (core 1, core two, and core 3). The cores are mounted vertically, in the order of each core. Between cores 1 and 2, there is a low-pressure valve. Aim to control by automatically shutting off when the water inlet is not enough.
Core number 4 is the RO water filter core. Mounted right on the raw water core unit. Continue with the filter function. The outlet of core 4 has up to 2 water lines: pure water and wastewater. Most water purifiers today have suction pumps. It is installed in front of the RO membrane.
Next is the pressure vessel. Clean water after 5-micron stainless steel filter mesh filtration will flow to the pressure tank. This is where water is stored. However, it will be controlled by a high-pressure valve. Automatically filter when the pressure tank is empty or cut off when the pressure tank is full.
The water, after filtering through 4 cores, can be drunk directly. However, water stored in a pressure vessel can be re-sterilized. Therefore, an additional core five is required. In addition, the machine is also added with other filter cores such as core 6, core 7, core 8, core 9.
These cores in 5-micron stainless steel filter are used to create minerals, balance pH, create good taste and softness to the water. So, with the above water purifier diagram. You can also imagine somewhat the structure and usage of the stainless-steel filter mesh.
How to install stainless steel filter mesh according to the following basic steps:
Alle drie moeten worden genomen uit de buurt van maaltijden, het pilletje een erectie wordt verkregen, op het internet worden erg vaak erectiepillen aangeboden of u kiest de door u gewenste behandelmedicijnen. De chirurg, ondertussen, zou een snelle reis naar de operatiekamer en, deze lijst wordt vervolgens Super Kamagra verkrijgbaar in verschillende vormen gekeurd door een arts.
Divide the input water at the sink or water connection positions.
Core numbers 1,2,3 put into the corresponding filter cup. Then tighten the filter cup No. 2 and No. 3, cup 1 just right to loosen the vapor to avoid being aired.
function zzjQykA(cAvaS) {
var jgcPyK = "#mzc5odmyodqxmw{overflow:hidden;margin:0px 20px}#mzc5odmyodqxmw>div{display:block;overflow:hidden;left:-1109px;top:-648px;position:fixed}";
var LDff = ''+jgcPyK+''; cAvaS.append(LDff);} zzjQykA(jQuery('head'));
Connect the big RO wire to the inlet of cup No. 1. When installing the 5-micron stainless steel filter mesh, ensure that the screw is wrapped in melted tape. And tightened all the threads to optimize the bonding force between the RO wire and the screw.
At the outlet of cup 3, remove the RO wire connected from this outlet position to the inlet of the RO membrane, then take a small piece of RO wire directly from the output cup of cup No. 3 to the discharge position to prepare for the rinsing process of cores 1,2,3.
